Home / Wood Stains and Dyes / Arm-R-Seal Oil Based Topcoat

Arm-R-Seal Oil Based Topcoat

Arm-R-Seal Oil Based Topcoat

$27.25

for 1 x

Arm-R-Seal Topcoats are made with the highest-quality urethane resin, making them extremely durable and long-lasting. These oil-based finishes are formulated to be wiped on with a cloth or applied with a foam brush, and they penetrate to provide deep-down protection for that “natural” look.

Size

Sheen

$25.41

Description

Arm-R-Seal Topcoats are made with the highest-quality urethane resin, making them extremely durable and long-lasting. These oil-based finishes are formulated to be wiped on with a cloth or applied with a foam brush, and they penetrate to provide deep-down protection for that “natural” look.

Color tone: Warm amber tone.
Arm-R-Seal Oil Based Urethane will continue to darken over time.

Oil Based Ambering: Yes
Sheens: Gloss, Semi-Gloss, Satin
Interior or Exterior: Interior Use
Product Type: Oil Based Urethane

Coats: 3 coats recommended
Coverage: Quart, 100 Sq. Ft. — Gallon, 400 Sq. Ft.
Viscosity: N/A

Application Method: Brush or Roll
Brushable: Yes Sprayable: *Yes
Spray Tip Sizes: HVLP .043-.051 Medium Air Cap

APPLICATOR CLEANUP: Mineral Spirits

DURABILITY
Durability (Highest, High, Medium, Low): Highest
Hardness (Koeing): 77
Wear (Taber): 57.1 mg loss
Water (5 max): 5
Chemical (105 max): 99

DRY TIMES:
Touch: 12 hrs.
To Re-coat: 24 hrs.
Before Light Use: 7-10 days
Until Complets Cure: 30 days

VOC: <540 g/L

DRY TIME: 7 days. Good ventilation, air movement and higher temperatures will accelerate dry time.
Cooler temperatures will slow dry time.

CURE TIME: 30 days under ideal conditions (70 degrees and 70% humidity).
Cure time is the amount of time needed for the finish on a piece to reach maximum hardness and be ready for normal use. This is different than “dry time.”  During the curing stage, treat the item with special care.
Avoid placing heavy objects on it.

CARE AND MAINTENANCE:
Always avoid the use furniture polishes, dusting sprays or oil soaps
as they may contaminate the finish for future recoating.
Use a water dampened cloth for regular cleaning.

WATER SPILLS AND DAILY USE: Clean water spills up as they occur during regular use and protect from heat. Although General Finishes products are water resistant, they are not impervious to water. Surfaces will not be damaged by spilled water so long as it is cleaned up promptly. We recommend using coasters to protect your wood from standing water and pot holders to protect from heat.

PREVENT SPONTANEOUS COMBUSTION: This is a combustible product.
Dispose of product soaked rags for all oil base products in accordance with local ordinances.

CLEANING YOUR FINISH: Clean with a water-damp rag.
Do NOT clean until the finish has cured completely (30 days).
If your surface requires deep cleaning due to grease or grime, add a speck of detergent or a bit of vinegar.

Avoid using oil-soap or silcone-based daily cleaners such as Pledge, Endust or Murphy’s Oil.

SANDING:
On bare wood sand to 150 or 180. Can be wet sanded into the wood using 400-600 grit.
Wipe off excess after sanding.

COMPATIBILITY: Can also be used over Danish Oil, Lin- seed Oil & Tung Oil once they are dry.

 

Product Warnings

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Description

Arm-R-Seal Topcoats are made with the highest-quality urethane resin, making them extremely durable and long-lasting. These oil-based finishes are formulated to be wiped on with a cloth or applied with a foam brush, and they penetrate to provide deep-down protection for that “natural” look.

Color tone: Warm amber tone.
Arm-R-Seal Oil Based Urethane will continue to darken over time.

Oil Based Ambering: Yes
Sheens: Gloss, Semi-Gloss, Satin
Interior or Exterior: Interior Use
Product Type: Oil Based Urethane

Coats: 3 coats recommended
Coverage: Quart, 100 Sq. Ft. — Gallon, 400 Sq. Ft.
Viscosity: N/A

Application Method: Brush or Roll
Brushable: Yes Sprayable: *Yes
Spray Tip Sizes: HVLP .043-.051 Medium Air Cap

APPLICATOR CLEANUP: Mineral Spirits

DURABILITY
Durability (Highest, High, Medium, Low): Highest
Hardness (Koeing): 77
Wear (Taber): 57.1 mg loss
Water (5 max): 5
Chemical (105 max): 99

DRY TIMES:
Touch: 12 hrs.
To Re-coat: 24 hrs.
Before Light Use: 7-10 days
Until Complets Cure: 30 days

VOC: <540 g/L

DRY TIME: 7 days. Good ventilation, air movement and higher temperatures will accelerate dry time.
Cooler temperatures will slow dry time.

CURE TIME: 30 days under ideal conditions (70 degrees and 70% humidity).
Cure time is the amount of time needed for the finish on a piece to reach maximum hardness and be ready for normal use. This is different than “dry time.”  During the curing stage, treat the item with special care.
Avoid placing heavy objects on it.

CARE AND MAINTENANCE:
Always avoid the use furniture polishes, dusting sprays or oil soaps
as they may contaminate the finish for future recoating.
Use a water dampened cloth for regular cleaning.

WATER SPILLS AND DAILY USE: Clean water spills up as they occur during regular use and protect from heat. Although General Finishes products are water resistant, they are not impervious to water. Surfaces will not be damaged by spilled water so long as it is cleaned up promptly. We recommend using coasters to protect your wood from standing water and pot holders to protect from heat.

PREVENT SPONTANEOUS COMBUSTION: This is a combustible product.
Dispose of product soaked rags for all oil base products in accordance with local ordinances.

CLEANING YOUR FINISH: Clean with a water-damp rag.
Do NOT clean until the finish has cured completely (30 days).
If your surface requires deep cleaning due to grease or grime, add a speck of detergent or a bit of vinegar.

Avoid using oil-soap or silcone-based daily cleaners such as Pledge, Endust or Murphy’s Oil.

SANDING:
On bare wood sand to 150 or 180. Can be wet sanded into the wood using 400-600 grit.
Wipe off excess after sanding.

COMPATIBILITY: Can also be used over Danish Oil, Lin- seed Oil & Tung Oil once they are dry.